BAD PDW MONOLITHIC LOWER RECEIVER

BAD PDW MONOLITHIC LOWER RECEIVER

BAD-PDW Monolithic PDW Lower Receiver VERT Stock System

BAD-PDW Monolithic PDW Lower Receiver VERT Stock System

BAD PDW MONOLITHIC LOWER RECEIVER

BAD PDW MONOLITHIC LOWER RECEIVER

BAD PDW MONOLITHIC LOWER RECEIVER

BAD PDW MONOLITHIC LOWER RECEIVERBAD PDW MONOLITHIC LOWER RECEIVER integrates a monolithic adjustable PDW stock which is the result of a collaboration between BAD and Cross Machine Tool

BAD PDW MONOLITHIC LOWER RECEIVER

BAD PDW MONOLITHIC LOWER RECEIVER

VERT  PDW Lower – MODEL: BAD-PDW Monolithic PDW Lower Receiver + Stock System

  • Built-In PDW Stock System
  • Ultra Compact Design – 4.75″ Stock Length for Ultimate Concealment
  • Proprietary Ultra Compact Buffer & Recoil Spring System – Compatible with MilSpec M16/AR15 Bolt Carrier
  • Self-Contained Buffer System – No Proprietary Bolt Carrier Required!  Ability to “Shotgun” the Upper
  • Monolithic Engineering – Receiver and PDW Stock Housing Precision CNC From Single Block of Billet 7075-T6 Aircraft Grade Aluminum for Superior Strength and Lightweight Design
  • Continuous Cheek Weld for Ultimate Comfort and Stability/Accuracy
  • Billet CNC Milled 7075-T6 Aluminum Buttstock
  • Build-In, Integral QD Sling Point at  Buttstock
  • Heat Treat & Harden S7 Tool Steel .315″ Dia. Guide Rods for Ultimate Impact Strength and Durability
  • No Metal-To-Metal Contact between Guide Rods and Receiver Housing
  • New Industry Standard in Smooth Stock Operation with Linear Motion Guide Bushings
  • (4) Locking Stock Positions – Lockable in Both Direction.  From 4.75″ Fully Collapsed to 8.75″ Fully Extended (measured from rear of receiver to end of stock)
  • Dimpled Locking Stops with Stainless Steel Ball Bearing & S7 Tool Steel Locking Latch
  • Ambidextrous Bolt Release (hardware included)
  • Ambidextrous Magazine Release (hardware included)
  • MIL-A-8625F, Type III, Class 2, Hard Anodized Flat Black Finish
  • Compatible with TDP/Mil Standard AR Lower Receiver Parts (except for built-in proprietary components)
  • Pictograph Selector Markings Properly Marked for 90° Safety or  BAD-ASS-ST / BAD-CASS-SA-ST Short Throw Ambidextrous Safety Selectors
  • Receiver Safety Selector Hole & Internal Wall Machined with Relief Cut for Battle Arms Development “SHORT-THROW / REVERSIBLE” Ambidextrous Safety Selectors
  • Multi Caliber Marking for Build Versatility
  • Flared, Deep Beveled Magwell
  • Easy in Install Set Screw Bolt Catch Pin (Pin Included)
  • Captured Takedown Pin Detent Spring (Set Screw Included)
  • Upper/Lower Receiver Tension Screw (Screw included)
  • Integrated Trigger Guard
  • All Components, material, and packaging made in the USA

BAD-PDW Monolithic PDW Lower Receiver VERT Stock System 2

BAD-PDW Monolithic PDW Lower Receiver VERT Stock System 2

Additional Components Include:

  • BAD-CASS-SA-ST – Combat Ambidextrous Safety Selector – 50°/90° Reversible – Standard & Short Lever
  • BAD-ATG – Battle Arms Development Adjustable Tactical Grip – 3 Grips-In-One – 3 Different Angles
  • BAD-EMMR-L-B – Enhanced Modular Magazine Release – Large Finger Pad – Black (Large Finger Pad may be replaced by Medium Finger Pad Pending Inventory Levels)
  • BAD-EPS – Enhanced Pin Set (Enhanced Pivot Pin & Enhanced Takedown Pin)
  • BAD-EBC – Enhanced Bolt Catch – CNC from Billet Steel
  • MilSpec Magazine Release & Spring
  • Bolt Catch Detent & Spring
  • Buffer Detent & Spring

Not Included:

  • Trigger Group (Trigger, Hammer, Disconnector, Trigger Pin, Hammer Pin, Trigger Spring, Hammer Spring, Disconnector Spring)

WARNINGS:

  • Will not work with solid filled 9mm bolt carrier
  • VERT TM buffer system is designed for 5.56/.223 direct gas impingement system 
  • VERT TM buffer system can work with piston driven AR if the rear, internal dimensions of the bolt carrier is Mil-Spec
  • Use of FAIL ZERO NICKLE BORON Bolt Carrier may cause damage to the buffer system due to the I.D. (Inside Diameter) of the BCG being undersized>
  • Inside, rear cavity of the bolt carrier must be .625″ diameter x .625″ deep minimum to clear the buffer.  Damage may occur if proper clearance isn’t met.

BAD PDW MONOLITHIC LOWER RECEIVER


UBR 2 0 COLLAPSIBLE AR15 STOCK | Magpul UBR

UBR 2 0 COLLAPSIBLE AR15 STOCK | Magpul UBR

MAGPUL UBR 2.0 COLLAPSIBLE AR15 STOCK

MAGPUL UBR 2.0 COLLAPSIBLE AR15 STOCK

MAGPUL UBR 2.0 COLLAPSIBLE AR15 STOCK

MAGPUL UBR 2.0 COLLAPSIBLE AR15 STOCK : is an adjustable stock for the AR15, M-16, AR-15, M4 designed to offer the same strength and stability as a fixed stock with a consistent and comfortable cheek weld in any position. An update of the revolutionary Utility/Battle Rifle (UBR) stock, the MAGPUL UBR 2 features a fixed cheek piece to provide a consistent cheek weld in any of its 8 positions, and is compatible with A5-length buffer systems. Designed to accommodate large bore AR calibers and withstand severe impacts, the MAGPUL UBR 2 comes standard with front and rear QD sling attachment points, a recessed footman’s loop, the ergonomic MOE SL angled-toe rubber butt-pad, and storage compartment. Buffer tube included, compatible with A5- length springs and buffers as well as carbine springs and buffers (with included spacer).

MAGPUL UBR 2.0 COLLAPSIBLE AR15 STOCK is an adjustable stock for the AR15, M-16, AR-15, M4, designed to offer the same strength and stability as a fixed stock with a consistent and comfortable cheek weld in any position.

An update of the revolutionary MAGPUL Utility/Battle Rifle (UBR) stock, the MAGPUL UBR 2 features a fixed cheek piece to provide a consistent cheek weld in any of its 9 positions, and is compatible with Carbine as well as A5-length buffer systems. Designed to accommodate large bore AR calibers and withstand severe impacts, the MAGPUL UBR 2 is nearly five ounces lighter while retaining all the durability its predecessor was legendary for. Comes standard with front and rear QD sling attachment points, two footman’s loops, the ergonomic MOE SL™ angled-toe rubber butt-pad, and customizable storage compartment. Made in U.S.A.

MAGPUL UBR 2.0 COLLAPSIBLE AR15 STOCK FEATURES

  • Mounts on a durable custom Receiver Extension tube (included) to accommodate the common M4 carbine buffer and spring as well as aftermarket A5 buffer systems*
  • Solid “fixed stock” lockup and consistent cheek weld in all positions
  • 9-Position LOP adjustability
  • Adjustment lever requires only gross motor movement to operate yet the entire stock remains streamlined and anti-snag
  • Enhanced lock mechanism with dual locking pawls for maximum drop strength and shock resistance
  • Multi-shell construction provides solid foundation and shields critical operating parts from penetration damage
  • Sloping cheek weld combines a slim profile with user comfort
  • Storage Compartment in tail of stock is removable and the door is reversible for user preference
  • Rubber butt-pad offers an anti-slip surface and increases impact protection
  • Rollover on the toe allows for easier shoulder transitions and better fit when using body armor
  • Sling Mounts
    • Front – QD swivel mount for ambidextrous one-point QD sling mounting
    • Left/Right Rear – Rotation-limited QD swivel sling mounts fit up to 1.5″ push-button swivels
    • Bottom – 1.25″ sling loop (additional loop accessible when Storage Compartment is removed)

MAGPUL UBR 2.0 COLLAPSIBLE AR15 STOCK SPECIFICATIONS

  • Weight, w/Receiver Extension: 21.3 oz.
  • Length: 8.5-12.5 in.
  • Width, max: 1.7 in.
  • LOP Adjustment Range: 4.0 in.
  • LOP, M4 Collapsed: ~11.6 in.
  • LOP, M4 Extended: ~15.6 in.

 

The MAGPUL UBR 2 includes the required custom Receiver Extension tube, Buffer Spacer, and all mounting hardware. A carbine buffer and spring (M4 or SR25 length) or A5 buffer and spring are required for use with the UBR and are not included.

AXTS RAPTOR

AXTS RAPTOR


AR15 Wood Stock Set | AR 15 Wood Stock

AR15 Wood Stock | AR 15 Wood Stock

AR15 Wood Stock

 

Brownells is now stocking the Lucid AR15 Wood Stock Sets in 6 variations.

We have to topics on the subject at the 308AR.com Forum. 

The Next 5.56 Project in the works

308 AR Wood Furniture

 

AR-15 Wood Stock Set – Beautifully finished stock sets in good-looking laminate or fancy AAA-grade American Walnut give your AR that “trophy” rifle look without altering its shooting capabilities. Each set consists of an A2-style buttstock with an integral cheek rest for a comfortable cheek-weld, plus an ergonomically contoured pistol grip, and a hand-filling forearm similar in shape to the original triangular M16 handguard.

Handguard has a convenient groove in each side to help locate the support hand and give you a secure grasp for excellent recoil control. Snaps on using your rifle’s existing handguard cap and delta ring—no gunsmithing, no permanent alterations to gun.

Pistol grip has finger grooves, a palm swell, and a gently curved backstrap to give you a solid, comfortable purchase.

Buttstock fits a standard A2-length buffer tube (available separately). Includes front sling stud that mounts on the underside of the handguard.

Laminate model available in Brown or red-brown/gray/dark green Camouflage that blends with a wide variety of landscapes. Buttstock accepts a standard A2-style buttplate or aftermarket pad, and includes a cutout to accept an M16-style rear sling loop.

Walnut model has the fancy grain pattern of a fine bolt action rifle, and comes with standard sling swivel stud and rubber buttpad installed.

AR15 Wood Stock Set

AXTS RAPTOR

AXTS RAPTOR

%d bloggers like this: