BAD PDW MONOLITHIC LOWER RECEIVER
BAD-PDW Monolithic PDW Lower Receiver VERT Stock System
BAD PDW MONOLITHIC LOWER RECEIVER
BAD PDW MONOLITHIC LOWER RECEIVER
BAD PDW MONOLITHIC LOWER RECEIVER – BAD PDW MONOLITHIC LOWER RECEIVER integrates a monolithic adjustable PDW stock which is the result of a collaboration between BAD and Cross Machine Tool
BAD PDW MONOLITHIC LOWER RECEIVER
VERT PDW Lower – MODEL: BAD-PDW Monolithic PDW Lower Receiver + Stock System
- Built-In PDW Stock System
- Ultra Compact Design – 4.75″ Stock Length for Ultimate Concealment
- Proprietary Ultra Compact Buffer & Recoil Spring System – Compatible with MilSpec M16/AR15 Bolt Carrier
- Self-Contained Buffer System – No Proprietary Bolt Carrier Required! Ability to “Shotgun” the Upper
- Monolithic Engineering – Receiver and PDW Stock Housing Precision CNC From Single Block of Billet 7075-T6 Aircraft Grade Aluminum for Superior Strength and Lightweight Design
- Continuous Cheek Weld for Ultimate Comfort and Stability/Accuracy
- Billet CNC Milled 7075-T6 Aluminum Buttstock
- Build-In, Integral QD Sling Point at Buttstock
- Heat Treat & Harden S7 Tool Steel .315″ Dia. Guide Rods for Ultimate Impact Strength and Durability
- No Metal-To-Metal Contact between Guide Rods and Receiver Housing
- New Industry Standard in Smooth Stock Operation with Linear Motion Guide Bushings
- (4) Locking Stock Positions – Lockable in Both Direction. From 4.75″ Fully Collapsed to 8.75″ Fully Extended (measured from rear of receiver to end of stock)
- Dimpled Locking Stops with Stainless Steel Ball Bearing & S7 Tool Steel Locking Latch
- Ambidextrous Bolt Release (hardware included)
- Ambidextrous Magazine Release (hardware included)
- MIL-A-8625F, Type III, Class 2, Hard Anodized Flat Black Finish
- Compatible with TDP/Mil Standard AR Lower Receiver Parts (except for built-in proprietary components)
- Pictograph Selector Markings Properly Marked for 90° Safety or BAD-ASS-ST / BAD-CASS-SA-ST Short Throw Ambidextrous Safety Selectors
- Receiver Safety Selector Hole & Internal Wall Machined with Relief Cut for Battle Arms Development “SHORT-THROW / REVERSIBLE” Ambidextrous Safety Selectors
- Multi Caliber Marking for Build Versatility
- Flared, Deep Beveled Magwell
- Easy in Install Set Screw Bolt Catch Pin (Pin Included)
- Captured Takedown Pin Detent Spring (Set Screw Included)
- Upper/Lower Receiver Tension Screw (Screw included)
- Integrated Trigger Guard
- All Components, material, and packaging made in the USA
BAD-PDW Monolithic PDW Lower Receiver VERT Stock System 2
Additional Components Include:
- BAD-CASS-SA-ST – Combat Ambidextrous Safety Selector – 50°/90° Reversible – Standard & Short Lever
- BAD-ATG – Battle Arms Development Adjustable Tactical Grip – 3 Grips-In-One – 3 Different Angles
- BAD-EMMR-L-B – Enhanced Modular Magazine Release – Large Finger Pad – Black (Large Finger Pad may be replaced by Medium Finger Pad Pending Inventory Levels)
- BAD-EPS – Enhanced Pin Set (Enhanced Pivot Pin & Enhanced Takedown Pin)
- BAD-EBC – Enhanced Bolt Catch – CNC from Billet Steel
- MilSpec Magazine Release & Spring
- Bolt Catch Detent & Spring
- Buffer Detent & Spring
Not Included:
- Trigger Group (Trigger, Hammer, Disconnector, Trigger Pin, Hammer Pin, Trigger Spring, Hammer Spring, Disconnector Spring)
WARNINGS:
- Will not work with solid filled 9mm bolt carrier
- VERT TM buffer system is designed for 5.56/.223 direct gas impingement system
- VERT TM buffer system can work with piston driven AR if the rear, internal dimensions of the bolt carrier is Mil-Spec
- Use of FAIL ZERO NICKLE BORON Bolt Carrier may cause damage to the buffer system due to the I.D. (Inside Diameter) of the BCG being undersized>
- Inside, rear cavity of the bolt carrier must be .625″ diameter x .625″ deep minimum to clear the buffer. Damage may occur if proper clearance isn’t met.
